If you are comparing a 320mm Filter Press, I recommend treating “320mm” as a plate or filter-area designation rather than a complete machine specification. The correct purchase decision depends on filtration area, chamber volume, plate material, operating pressure, pump configuration, cake moisture targets, and the characteristics of your slurry. In automotive applications, this equipment may be considered for wastewater, coolant filtration, metalworking-fluid treatment, paint sludge, washing water, or other solid-liquid separation duties, but the final configuration must be matched to the actual process.
You can find more information on our web, so please take a look.
In this guide, I explain the specifications I would request, how I would compare suppliers, and which questions can prevent an unsuitable quotation. I also show where Jingwo can support a B2B buyer with configuration discussion, documentation, and pre-sales selection assistance.
This guide is intended for automotive component manufacturers, vehicle service operations, metalworking plants, wastewater contractors, equipment integrators, and industrial distributors. It is also useful for purchasing teams that receive several filter press quotations with different terminology and incomplete technical details. I focus on practical comparison points rather than presenting one fixed specification as suitable for every plant.
The guide is especially relevant when you need to separate suspended solids from process water, polishing liquids, washing wastewater, coolant-related streams, or paint and coating residues. Because these slurries can differ significantly in particle size, oil content, temperature, and chemical compatibility, I recommend using the machine specification together with a process description.
A 320mm Filter Press normally refers to a compact filter press family identified by an approximately 320 mm plate dimension or nominal plate format. The exact meaning can vary between manufacturers, so I would not use the name alone to calculate capacity. A quotation should clearly state whether 320mm describes the plate width, plate diameter, filter chamber size, or another model reference.
A filter press separates solids from liquid by pumping slurry into filter chambers formed between plates and filter cloths. Pressure drives liquid through the cloth while the retained solids form a filter cake. After the chamber is filled, the press is opened and the cake is removed before the next cycle begins.
In automotive and motorcycle manufacturing, a filter press may help reduce suspended solids in wastewater or recover solids from selected process streams. Possible duties include treatment of parts-washing wastewater, machining-related fluids, paint sludge, grinding residues, and cleaning operations. Suitability depends on whether the stream contains free oil, emulsified oil, abrasive particles, hazardous chemicals, or materials that may blind the filter cloth.
I would therefore ask the buyer to define the actual goal first: cleaner filtrate, lower sludge volume, solids recovery, water reuse, or protection of downstream equipment. A machine optimized for clear filtrate may not be identical to one selected for rapid cake discharge or high solids throughput. The process objective determines which specifications deserve priority.
Confirm the plate dimensions and the number of plates included in the quotation. The number of plates affects the total chamber volume and filtration area, but the relationship depends on plate design, chamber depth, and effective filtering surface. I recommend asking for both total filtration area in square metres and effective chamber volume in cubic metres, rather than relying on the plate count alone.
For reference, 320mm equals 0.32m, but this conversion does not indicate the machine’s usable capacity. A small press can still have different performance depending on its plate arrangement and cloth design. The supplier should provide a dimensional drawing showing the overall length, width, height, inlet position, and maintenance clearance.
Pressure influences liquid removal and cake formation, but higher pressure is not automatically better. The correct level depends on particle structure, cloth permeability, slurry viscosity, and the mechanical limits of the plates, hydraulic system, pump, and frame. As an example of a value that must be confirmed rather than assumed, a quotation may specify a maximum working pressure of 1.0 MPa; buyers should verify whether this is the pump pressure, chamber pressure, or design rating.
I recommend requesting separate values for recommended operating pressure, maximum allowable pressure, and hydraulic closing pressure. These details help prevent confusion between normal operation and equipment safety limits. The supplier should also explain whether pressure monitoring, gauges, or protective devices are included.
Filter cloth selection should be based on particle size, chemical compatibility, temperature, cake release, and required filtrate clarity. Common cloth materials may include polypropylene, polyester, or other engineered fabrics, but the correct choice cannot be determined from the 320mm size alone. For automotive wastewater, oil-containing streams and cleaning chemicals should be identified before the cloth is selected.
Plate materials also require confirmation. Polypropylene plates are commonly considered for many industrial liquid-solid separation duties because of their chemical resistance, while other materials may be appropriate for different temperatures or process conditions. I recommend asking for the plate material, cloth material, temperature limit, chemical compatibility guidance, and replacement part identification.
You will get efficient and thoughtful service from Jingwo.
The feed pump must match slurry concentration, viscosity, solids content, pipework, and the required pressure profile. Pump type, flow rate, motor power, inlet size, and control method should appear in the quotation instead of being left as unspecified accessories. A motor value such as 2.5 kW may appear in an example configuration, but it should never be treated as a standard 320mm requirement without checking the selected pump and duty.
Cycle time is also process-dependent. It includes filling, filtration, possible washing or air blowing, pressure holding, opening, cake discharge, and cleaning. I would ask the supplier to separate these stages and state whether any cycle-time estimate is based on actual slurry testing, pilot data, or an engineering approximation.
Start with a representative description of the feed. Record flow rate, solids concentration, particle characteristics, temperature, pH, oil content, chemical additives, and the desired filtrate quality. If the feed changes during production, provide minimum, normal, and peak conditions so the supplier can assess whether one configuration is adequate.
State whether your priority is a dry and easily handled cake, cleaner liquid, high throughput, low operator involvement, or reduced water consumption. These objectives can conflict with one another, so the supplier needs to understand which result is most important. Also identify whether the cake will be disposed of, recycled, dewatered further, or returned to a process.
Compare filtration area, chamber volume, plate quantity, cloth type, operating pressure, pump details, frame material, control method, and discharge arrangement. Then check utilities, including electrical supply, compressed air requirements if applicable, drainage, installation space, and maintenance access. A quotation with a lower initial price may not represent lower total cost if pumps, cloths, controls, or spare parts are excluded.
When the slurry is difficult, I recommend representative testing before finalizing the purchase. Testing can help evaluate cake formation, filtrate clarity, cloth selection, approximate cycle behavior, and cleaning requirements. If testing is not practical, provide laboratory data and request that all assumptions and exclusions be written into the offer.
The most common mistake is assuming that every 320mm Filter Press has the same capacity. Model names are not a substitute for filtration area, chamber volume, or a defined duty point. Another frequent problem is selecting a cloth based only on price, without considering particle retention, chemical exposure, and cake release.
Buyers also sometimes overlook the handling method after filtration. Manual cake discharge may be acceptable for intermittent use, while frequent production may require a more convenient opening arrangement, drip trays, or improved operator access. I would also confirm whether the quoted machine includes feed pump, filter cloths, pressure gauge, hydraulic components, control cabinet, installation instructions, and recommended spare parts.
Pricing depends on plate count, filtration area, materials, automation, pump selection, electrical standard, accessories, and packaging requirements. There is no responsible way to give one universal price for a 320mm Filter Press without these details. Ask whether the offer is for one complete machine, a semi-finished unit, or a base press requiring separately purchased accessories.
For procurement planning, request the minimum order quantity, production lead time, inspection procedure, packing method, warranty scope, and spare-parts availability. Lead time should be confirmed against the actual configuration and quantity, particularly when customized frames, non-standard voltage, special cloths, or control components are required. All delivery assumptions should be documented before issuing a purchase order.
At Jingwo, I would begin with the process rather than recommend a model from the keyword alone. Our technical discussion should cover slurry composition, required capacity, target cake condition, filtration pressure, materials, operating environment, and the buyer’s installation constraints. This approach helps us prepare a more useful quotation for manufacturers, distributors, and project integrators.
We can support the specification review by clarifying the proposed plate arrangement, filter cloth requirements, pump configuration, dimensions, and included components. For export projects, buyers should also provide destination voltage, preferred documentation, packaging expectations, and local installation conditions. Where the application is uncertain, I recommend a staged evaluation using samples, laboratory information, or a pilot arrangement before committing to a larger system.
The right 320mm Filter Press is not selected by size label alone. I recommend confirming the meaning of 320mm, defining the slurry and output objective, comparing filtration area and chamber volume, checking materials and pressure limits, and reviewing the complete supply scope. For automotive applications, special attention should be given to oil, chemicals, abrasive solids, cloth compatibility, and cake-handling requirements.
Your next step should be to prepare a process data sheet with feed volume, solids information, temperature, chemistry, desired filtrate quality, and operating schedule. Send those details to Jingwo together with your required plate format, power standard, and delivery location, and we can help develop a technically clearer 320mm Filter Press quotation for comparison and procurement.
Want more information on 320mm Filter Press? Feel free to contact us.